What is Ultrasonic Testing? |
Ultrasonic nondestructive testing, also known as ultrasonic NDT or simply UT, is a method of characterizing the thickness or internal structure of a test piece through the use of high frequency sound waves. The frequencies, or pitch, used for ultrasonic testing are many times higher than the limit of human hearing, most commonly in the range from 500 KHz to 20 MHz.
|
How does it work? |
High frequency sound waves are very directional, and they will travel through a medium (like a piece of steel or plastic) until they encounter a boundary with another medium (like air), at which point they reflect back to their source. By analyzing these reflections it is possible to measure the thickness of a test piece, or find evidence of cracks or other hidden internal flaws.
|
What sort of materials can be tested? |
In industrial applications, ultrasonic testing is widely used on metals, plastics, composites, and ceramics. The only common engineering materials that are not suitable for ultrasonic testing with conventional equipment are wood and paper products. Ultrasonic technology is also widely used in the biomedical field for diagnostic imaging and medical research.
|
What are the advantages of ultrasonic testing? |
Ultrasonic testing is completely nondestructive. The test piece does not have to be cut, sectioned, or exposed to damaging chemicals. Access to only one side is required, unlike measurement with mechanical thickness tools like calipers and micrometers. There are no potential health hazards associated with ultrasonic testing, unlike radiography. When a test has been properly set up, results are highly repeatable and reliable.
|
What are the potential limitations of ultrasonic testing? |
Ultrasonic flaw detection requires a trained operator who can set up a test with the aid of appropriate reference standards and properly interpret the results. Inspection of some complex geometries may be challenging. Ultrasonic thickness gages must be calibrated with respect to the material being measured, and applications requiring a wide range of thickness measurement or measurement of acoustically diverse materials may require multiple setups. Ultrasonic thickness gages are more expensive than mechanical measurement devices.
|
What is an ultrasonic transducer? |
A transducer is any device that converts one form of energy into another. An ultrasonic transducer converts electrical energy into mechanical vibrations (sound waves), and sound waves into electrical energy. Typically, they are small, hand-held assemblies that come in a wide variety of frequencies and style to accommodate specific test needs.
|
What is an ultrasonic thickness gage? |
An ultrasonic thickness gage is an instrument that generates sound pulses in a test piece and very precisely measures the time interval until echoes are received. Having been programmed with the speed of sound in the test material, the gage utilizes that sound velocity information and the measured time interval to calculate thickness via the simple relationship [distance] equals [velocity] multiplied by [time].
|
How accurate is ultrasonic thickness gaging? |
Under optimum conditions, commercial ultrasonic gages can achieve accuracies as high as +/- 0.001 mm (0.00004"), with accuracies of +/- 0.025 mm (0.001") or better possible in most common engineering materials. Factors affecting accuracy include the uniformity of sound velocity the test material, the degree of sound scattering or absorption, the surface condition, and the accuracy and care with which the instrument has been calibrated for the application at hand.
|
Who uses ultrasonic gages? |
A major use for ultrasonic gages is the measurement of remaining wall thickness in corroded pipes and tanks. The measurement can be made quickly and easily without needing access to the inside or requiring the pipe or tank to be emptied. Other important applications include measuring the thickness of molded plastic bottles and similar containers, turbine blades and other precision machined or cast parts, small diameter medical tubing, rubber tires and conveyor belts, fiberglass boat hulls, and even contact lenses.
|
What is an ultrasonic flaw detector? |
Sound waves traveling through a material will reflect in predictable ways off of flaws such as cracks and voids. An ultrasonic flaw detector is an instrument that generates and processes ultrasonic signals to create a waveform display that can be used by a trained operator to identify hidden flaws in a test piece. The operator identifies the characteristic reflection pattern from a good part, and then looks for changes in that reflection pattern that may indicate flaws.
|
What kind of flaws can you find with one? |
A wide variety of cracks, voids, disbonds, inclusions, and similar problems that affect structural integrity can all be located and measured with ultrasonic flaw detectors. The minimum detectable flaw size in a given application will depend on the type of material being tested and the type of flaw under consideration.
|
Who uses ultrasonic flaw detectors? |
Ultrasonic flaw detectors are widely used in critical safety-related and quality-related applications involving structural welds, steel beams, forgings, pipelines and tanks, aircraft engines and frames, automobile frames, railroad rails, power turbines and other heavy machinery, ship hulls, castings, and many other important applications.
|
What other types of instruments are available? |
| Ultrasonic imaging systems are used to generate highly detailed pictures similar to x-rays, mapping the internal structure of a part with sound waves. Phased array technology originally developed for medical diagnostic imaging is used in industrial situations to create cross-sectional pictures. Large scanning systems are used by the aerospace industry and metalworking suppliers to check for hidden flaws in both raw materials and finished parts. Ultrasonic pulser/receivers and signal analyzers are used in a variety of materials research applications. |
MT warning |
1.When use hand yokes, it must be avoid to working with carrying idler, because it will bring improving temperature or damage.
2.When use the poles, the surface of poles must keep excellent touch with tested parts. Then press the button of handle of hand yoke for charging magnetism, there will be a best effect of flaw detection. And the poles must be avid to be hit, fallen off, it should be clean.
3.During use, if the coil of poles is badly heated, please stop using and check the reason of trouble. Use again after repaired, or else the poles will be damaged.
4.After used, the switchs of units and electrical panel should be cutted.
5.After inspecting, it should be done: clean the sundries of turning joints and filling lubrication oil. |
PT Warning |
1.do not spray to the human body and utensils.
2.do not insolate under sunlight.
3.it should be far away from kindling at the scene.
4.use clean water to rinsing after it carelessly comes into the eyes and skin.
5.do your best to using protective gloves.
6.do not let children play with liquid for fear any accidents.
7.note ventilation for closed-vessel.
|
